Bendix™ BlindSpotter®Side Object Detection SystemInstallation GuideBendix™ BlindSpotter®Side Object Detection SystemBW2798 (Formerly VOIG0032)April 20
8Installation ProcedureSensor LocationThe Bendix™ BlindSpotter® Side Object Detection Sensor should be mounted on the side of the vehicle, between 22
9Installation ProcedureSensor OrientationThe Bendix™ BlindSpotter® Side Object Detection Sensor should be orientated so the embossed logo is parallel
10Installation ProcedureMounting the SensorThe sensor should be mounted to the vehicle using 10-24 (6 mm) stainless steel hardware. Bolts should be in
11Installation ProcedureSide Object Display MountingThe Bendix™ BlindSpotter® Side Object Detection Display Unit should be mounted on the inside of th
12Installation ProcedureComponent ConnectorsSIDE OBJECT DETECTION SENSOROPERATORDISPLAYUNITODU P11234123456CONNECTOR REARCONNECTOR REAR
13Installation ProcedureHarness Connector Pin-OutJ1 - Deutsch Part Number DT04-4PJ2 - Deutsch Part Number DT04-6PPin 1 J2 - Pin 4Pin 2 J2 - Pin 5Pin 3
14Installation ProcedureHarness Layout Diagram
15Operation TestingTesting System Operation1. Before testing the system, move the vehicle to an area where there are no objects within a minimum of a
16Operation TestingTesting Sensor DetectionTo test the sensor's maximum effective detection capabilities, use a fl at metallic object with a minim
17TroubleshootingSystem Fault IndicationIf both the red and yellow LEDs remain illuminated continuously after fi ve seconds of initial power-up, or any
18TroubleshootingRed Detection LED Remains OnIf after the initial fi ve second system power-up test, the red detect indicator remains illuminated const
19TroubleshootingNo Objects DetectedIf after the initial system power-up the sensor does not appear to detect any objects, the radar sensor may have m
General Information20J1DisplayJ1DisplayTroubleshootingNo Audible ToneWhen an object is detected while the vehicle's turn signal is active, but th
21J1DisplayJ2SensorTroubleshootingSystem Does Not Power-UpWhen the vehicle's ignition switch is turned to the on position and the side object dis
22TroubleshootingWiring DiagramsJ2 SODODU PWRODU GNDCOMMPWRGNDSIDE OBJECT DETECTION SENSORJ1 ODUODU PWRODU GNDODU COMMTURN SIGNALOPERATORDISPLAYUNITOD
23TroubleshootingJ2J13214562134J1 ODUDISPLAYSENSORJ2 SOD72 INCHES240 INCHES1234563421PWRGNDCOMMODU PWRODU GNDREDBLACKWHITEDK GREENBROWNREDBLACKIGNITIO
24Specifi cationsTypical: Electronics Solid state Sealing Encapsulated to protect from dust, moisture, and vibration. Operating Temperature -40°F
25Specifi cationsRegulatory Compliance: Compliant with FCC Part 15.249 (5725-5875 MHz) FCC ID OXZSTDPREVIEW
26WarrantyManufacturer Limited WarrantyThe Bendix standard warranty specifi c to retrofi t systems is 12 months/100,000 miles when the product is instal
General Information1Table of ContentsGeneral InformationWarnings and Cautions ...
BW2798 ©2013 Bendix Commercial Vehicle Systems LLC, a member of the Knorr-Bremse Group All Rights Reserved • 04/13Bendix Commercial Vehicle Systems L
General Information2Warnings and Cautions▲WARNING!▲WARNING!Improper use of this system could lead to a serious accident. Read this entire Installation
General Information3▲WARNING!People’s lives depend on the proper installation of this product in conformance with these instructions. It is necessary
4FCC Compliance StatementFederal Communications CommissionThis device complies with Part 15 of the FCC (Federal Communications Commission) rules. Oper
5System OverviewProduct DescriptionThe Bendix™ BlindSpotter® Side Object Detection System is a pulse-modulated radar system capable of detecting the p
6System OperationSystem OperationThe Bendix™ BlindSpotter® Side Object Detection System is powered by the vehicle's ignition switch, and consists
7System OperationSide Object Detection DisplayThe display unit has two bright LED indicators used to display the system status. A yellow LED indicates
Comments to this Manuals